Gravel & Stone Calculator
Enter your area and depth and get cubic yards, tons, bags and cost for gravel, crushed stone, river rock and more – with real material densities and the waste allowance already built in.
- Yards, tons, bags & cost
- US & metric units
- Free, no sign-up
Add a price for a cost estimate
How this was calculated
Results update live – no submit button, no page reload, works on any phone.
Each material has its own density, so #57 stone, pea gravel and sand give different tonnages – not one generic number.
Base layers compact 15–20%. Our calculators include an allowance so you do not run short on delivery day.
See how many 0.5 cu ft or 50 lb bags you would need, compare with bulk tons, and add your supplier's price.
On this page
How much gravel do I need?
To work out how much gravel you need, multiply the area you are covering by the depth of gravel to get a volume, then convert that volume to tons using the gravel’s density. Most gravel weighs about 1.4 US tons per cubic yard, so one cubic yard covers roughly 100 sq ft at 3 inches deep. The calculator above does all of this for you – including an allowance for waste – but here is the full method if you want to check the numbers by hand (or follow our step-by-step gravel guide with five worked examples).
Volume (ft³) = Length (ft) × Width (ft) × Depth (in) ÷ 12Cubic yards = Volume (ft³) ÷ 27Tons = Cubic yards × 1.4 (use the material’s own tons-per-yard figure from the table below)
Worked example: a 20 ft × 10 ft gravel pad, 4 inches deep
- Area: 20 × 10 = 200 sq ft
- Volume: 200 × (4 ÷ 12) = 66.7 ft³
- Cubic yards: 66.7 ÷ 27 = 2.47 yd³
- Tons: 2.47 × 1.42 (3/4″ gravel) = 3.5 tons
- Add 5–10% for waste and settling → order 3.7–3.9 tons (or 2.6–2.7 yd³)
How to use this gravel calculator
- Choose the shape and measure the area
Pick rectangle, circle or triangle and enter the dimensions in feet (or metres). For an odd-shaped bed, split it into simple shapes and use “Add another area” – the calculator adds them together. If you already know the square footage, choose “I know the area”.
- Set the depth
Enter the depth in inches, or tap a preset. Use 2–3″ for decorative beds and walkways, 3–4″ for patios and paths, and 4–6″ for driveways (ideally as a 4″ compacted base plus a 2″ top layer).
- Select the material
Choose the gravel or stone you are buying. Each option carries its own density – pea gravel is lighter than #57 stone, and crusher run is heavier than both – so the tonnage changes correctly. You can also type a custom density from your supplier’s spec sheet. Not sure which size to buy? Check the gravel sizes chart.
- Keep (or adjust) the waste allowance
The default 5% covers spillage and uneven ground. For a compacted base layer, raise it to 15–20% because dense-graded stone loses volume when it is rolled.
- Read your results and add a price
You get cubic yards, tons, cubic feet, kilograms and the number of bags. Open “Add price for a cost estimate”, enter your supplier’s price per ton, yard or bag plus any delivery fee, and the total cost appears instantly.
Gravel coverage chart: square feet per ton
One ton of gravel covers a different area depending on how deep you spread it. Use this chart to sanity-check your order or to work backwards from a number of tons you already have.
| Material | Density | Tons per yd³ | sq ft per ton at 2" | sq ft per ton at 3" | sq ft per ton at 4" | sq ft per ton at 6" |
|---|---|---|---|---|---|---|
| Gravel, 3/4"–1" (general) | 105 lb/ft³ | 1.42 | 114 | 76 | 57 | 38 |
| Pea gravel (3/8") | 96 lb/ft³ | 1.30 | 125 | 83 | 63 | 42 |
| Crushed stone #57 (3/4") | 105 lb/ft³ | 1.42 | 114 | 76 | 57 | 38 |
| Crusher run / #411 / ABC (dense) | 125 lb/ft³ | 1.69 | 96 | 64 | 48 | 32 |
| Stone dust / screenings | 100 lb/ft³ | 1.35 | 120 | 80 | 60 | 40 |
| River rock, 1–3" | 100 lb/ft³ | 1.35 | 120 | 80 | 60 | 40 |
| Decorative / landscape rock | 100 lb/ft³ | 1.35 | 120 | 80 | 60 | 40 |
| Lava rock | 50 lb/ft³ | 0.68 | 240 | 160 | 120 | 80 |
| Limestone, crushed | 100 lb/ft³ | 1.35 | 120 | 80 | 60 | 40 |
| Granite, crushed | 105 lb/ft³ | 1.42 | 114 | 76 | 57 | 38 |
| Recycled concrete | 95 lb/ft³ | 1.28 | 126 | 84 | 63 | 42 |
Coverage = 2,000 lb ÷ (density × depth in feet). Figures are for loose material; add 5–10% for waste and up to 20% for compacted base layers.
How deep should gravel be?
Depth is the number that most often goes wrong. Too shallow and soil shows through and weeds come up; too deep and you waste money and the gravel shifts underfoot. These are the depths landscapers and aggregate suppliers typically recommend (our gravel depth guide explains each one):
| Project | Recommended depth | Notes |
|---|---|---|
| Decorative beds & borders | 2–3″ | Lay landscape fabric first to stop weeds and sinking |
| Garden paths & walkways | 3–4″ | Edging keeps the gravel in place |
| Patio (gravel surface) | 3–4″ | Use angular gravel – it locks together better than pea gravel |
| Gravel driveway (new) | 8–12″ total | 4–6″ base of crusher run + 3–4″ middle + 2–3″ top gravel |
| Driveway top-up / resurfacing | 2–3″ | Only the top layer needs replacing |
| Shed or hot tub pad | 4–6″ | Compacted 3/4″ clean stone (#57) drains best |
| French drain / drainage | Fill trench | Use washed stone with no fines (3/4″–1 1/2″) |
| Under a concrete slab | 4–6″ | Compacted crusher run or #57, per local code |
Cubic yards vs. tons: which should I order?
Suppliers sell gravel by weight (tons) or by volume (cubic yards), and sometimes both. A cubic yard is a block 3 ft × 3 ft × 3 ft (27 cubic feet). Because gravel is roughly 1.4 tons per cubic yard, one ton is about 0.7 cubic yards. When you compare quotes, convert both to the same unit – a price per ton that looks cheap can cost more than a price per yard once you do the maths. Our calculator shows both so you can order in whichever unit your yard uses. For sand, soil and other materials, use our cubic yards to tons conversion table.
Tip: a standard full-size pickup carries about 1 cubic yard (≈1.4 tons) of gravel – and that is close to the payload limit of most half-ton trucks. Anything over 2–3 yards is normally cheaper to have delivered.
How much does gravel cost?
Prices vary a lot by region and stone type, so always get a local quote – but as a guide, common crushed stone, crusher run and pea gravel typically cost about $15–$45 per ton at the yard (roughly $20–$60 per cubic yard) and about $30–$75 per ton delivered, with decorative river rock and specialty stone costing more. Our gravel cost guide breaks prices down by type, ton, yard and truckload. Delivery is usually a flat fee for a truckload, which is why ordering everything in one trip saves money. Bagged gravel from home-improvement stores costs several times more per ton than bulk, but makes sense for jobs under about half a cubic yard. Enter your own quote in the calculator to see the total for your exact quantity. Planning a driveway? See the gravel driveway cost guide or use the gravel driveway cost calculator.
Frequently asked questions
How much does a cubic yard of gravel weigh?
A cubic yard of typical 3/4″ gravel or crushed stone weighs about 2,800 lb (1.4 US tons). Pea gravel is a little lighter at roughly 2,600 lb, while dense-graded crusher run can reach 3,400 lb (1.7 tons) per cubic yard because the fines fill the gaps between stones. See how much a yard of gravel weighs for every type.
How many square feet does a ton of gravel cover?
At 2 inches deep, one ton of 3/4″ gravel covers about 114 sq ft; at 3 inches about 76 sq ft; and at 4 inches about 57 sq ft. Lighter materials such as lava rock cover more; heavier ones such as crusher run cover less. The coverage chart above lists each material.
How many cubic yards of gravel do I need for a 10×10 area?
A 10 ft × 10 ft area is 100 sq ft. At 3 inches deep you need 25 cubic feet, which is 0.93 cubic yards (about 1.3 tons). At 4 inches it is 1.23 cubic yards (about 1.75 tons). Add 5–10% for waste.
How many bags of gravel equal a cubic yard?
A cubic yard is 27 cubic feet, so it takes 54 bags of 0.5 cu ft or 27 bags of 1 cu ft. Bagged gravel is convenient for small jobs but costs far more per yard than bulk delivery, so compare both in the calculator before you buy.
Should I buy gravel by the ton or by the cubic yard?
Either works – just compare like with like. Most gravel is about 1.4 tons per cubic yard, so a quote of $50 per ton equals about $70 per cubic yard. Our calculator shows both units for every material so you can order in whatever unit your supplier uses.
How much gravel do I need for a driveway?
A new gravel driveway needs 8–12 inches of material in layers: a 4–6″ compacted base of crusher run or road base, a 3–4″ middle layer of 2–3″ stone, and a 2–3″ top layer of 3/4″ gravel. For a 12 ft × 50 ft driveway that is roughly 20–30 tons in total. Use the calculator once per layer with the matching material and depth.
Does the calculator work in metric?
Yes. Switch to “Metric” at the top of the calculator and enter metres and centimetres. Results are shown in cubic metres and metric tonnes, with cubic yards and US tons alongside. Densities are converted automatically (1 lb/ft³ = 16.02 kg/m³).
How accurate is this gravel calculator?
The volume calculation is exact for the dimensions you enter. The weight depends on the density you choose; real-world gravel varies by around ±10% with moisture and stone size, which is why we include a waste allowance and let you enter your supplier’s exact density.
All stone, soil and sand calculators
Every calculator uses the same engine with densities matched to the material. Pick the one that fits your project: