Gravel & Stone Calculators

Gravel Driveway Calculator

How much gravel for a driveway – base, middle and top layers in tons, cubic yards and truckloads, for a new build or a top-up of an existing drive.

  • 3-layer build
  • Tons & truckloads
  • Free, no sign-up
Gravel Driveway Calculator
Base layer (large stone)
Density:lb/ft³
%
Middle layer (optional)
Density:lb/ft³
%
Top / surface layer
Density:lb/ft³
%
A proper gravel driveway is three layers (about 10–12" in total) over compacted subgrade: 4" of large #3/#4 stone, 3" of crusher run and 3" of #57 on top. For a light-duty refresh of an existing driveway, set the base and middle layers to zero.
stonegravelcalculator.com
Driveway estimate · all layers
Material–
Area0 sq ft
Layers–
0tons
0 cubic yards
Volume0
Weight0
Base layer (large stone)–
Middle layer (optional)–
Top / surface layer–
Truckloads0 ×
Est. cost–
Add a price for a cost estimate
How this was calculated
Estimate only. Densities are typical loose values – confirm with your supplier.
On this page

    A gravel driveway that lasts is built in layers, not dumped in one pile: a base of large #3/#4 stone that bridges soft ground, a middle layer of crusher run that locks the base together, and a top course of #57 or 3/4″ clean stone that drains and is comfortable to drive on. Each layer has its own depth, density and compaction, so a single “gravel” number is usually wrong by a third. This calculator prices each layer separately and adds them up – or set the base and middle layers to zero to work out a simple top-up of an existing driveway.

    How to use the gravel driveway calculator

    1. Enter length and width

      Measure the driveway in feet. Typical widths: 10–12 ft for a single car, 18–20 ft for two cars side by side. Add a second run for a turnaround or parking pad with “Add another run”.

    2. Set the base layer

      A new driveway gets 4″ of large #3/#4 stone (1.5–2.5″) – more on clay or wet ground. On firm, well-drained soil, or when you are only refreshing an existing drive, set the base depth to 0.

    3. Set the middle and top layers

      3″ of crusher run / #411 binds the base; 3″ of #57 is the standard top course. Prefer a hard, dust-free surface? Choose crusher run on top and compact it. Prefer a softer look? Pea gravel – but keep it to 2″.

    4. Read tons and truckloads

      The ticket lists each layer in tons and yards, then the total and how many truckloads it is (a tri-axle holds about 20 tons / 14 yards). Compaction allowances – 15% for base and middle, 10% for top – are built in.

    Gravel driveway formula

    Cubic yards per layer = Length (ft) × Width (ft) × Depth (in) ÷ 324
    Tons per layer = cubic yards × tons per yard × (1 + compaction)  ·  Total = base + middle + top

    Example: 50 × 12 ft driveway, standard 4″ + 3″ + 3″ build

    1. Area = 50 × 12 = 600 sq ft
    2. Base, 4″ of #3 stone: 7.41 yd³ × 1.35 t/yd³ × 1.15 = 11.5 tons
    3. Middle, 3″ of crusher run: 5.56 yd³ × 1.69 t/yd³ × 1.15 = 10.8 tons
    4. Top, 3″ of #57: 5.56 yd³ × 1.42 t/yd³ × 1.10 = 8.7 tons
    5. Total ≈ 31 tons (about 21 loose cubic yards) – two tri-axle loads

    How much gravel for a driveway? Quick reference

    DrivewayAreaTop-up only (3″ of #57)Full 3-layer build (10″)Truckloads (20 t)
    Single car, 20 × 10200 sq ft2.9 t10.3 t1
    Single car, 40 × 12480 sq ft6.9 t24.8 t1–2
    Single car, 50 × 12600 sq ft8.7 t30.9 t2
    Double, 40 × 20800 sq ft11.6 t41.3 t2–3
    Long drive, 100 × 121,200 sq ft17.3 t61.9 t3–4
    Long drive, 200 × 122,400 sq ft34.7 t123.8 t6–7

    Full build = 4″ #3 base + 3″ crusher run + 3″ #57, with 15/15/10% compaction allowances. Top-up = 3″ of #57 with 10% allowance (about 1.45 tons per 100 sq ft).

    Gravel driveway layers explained

    LayerMaterialDepthDensityWhy
    SubgradeNative soil, graded and compacted, geotextile fabric on clay––Stops gravel sinking into mud
    Base#3 / #4 clean stone (1.5–2.5″), or recycled concrete4″ (6″ on soft ground)≈1.35 t/yd³Spreads the load, drains
    MiddleCrusher run / #411 / ABC / 2A3″≈1.69 t/yd³Fines lock the big stone together
    Top#57 (3/4″) or 3/4″ clean; pea gravel for looks2–3″≈1.42 t/yd³Drains, self-heals, comfortable to drive on

    Total depth for a new residential driveway is about 10–12 inches. A driveway that only sees cars on firm ground can get away with 6–8″; a farm lane or anything a delivery truck uses needs 12″ or more. Compact each layer before adding the next, and crown the surface 2–3% (about 1/4″ per foot) so water runs off.

    Which gravel for the top layer?

    • #57 crushed stone (3/4″) – the default. Angular, locks together, drains, stays put. Slightly noisy. #57 stone calculator.
    • Crusher run / 3/4″ minus – compacts into a hard, smooth surface that is easy to plow. Dusty when dry, puddles when wet. Needs 15–20% extra for compaction.
    • Pea gravel – rounded and attractive, but it rolls under tires and migrates; keep it to 2″ over a crusher-run base with edging. Pea gravel calculator.
    • Decomposed granite – a natural, compacted look popular in the West; stabilized DG resists ruts.
    • Recycled asphalt millings – binds in summer heat into a near-paved surface; cheap where available.

    How many truckloads is that?

    A standard tri-axle dump truck carries 20–22 tons (about 14–15 cubic yards of stone). A single-axle truck carries 8–10 tons; a tandem 14–16 tons; a pickup about half a ton (one scoop, roughly 1/2 yard). For the 50 × 12 example above – 31 tons – that is two tri-axle loads, so order one of base and one mixed, or three smaller loads delivered as you build each layer.

    Gravel driveway cost

    Material for a full 10″ build runs about $1.50–$3.00 per square foot ($900–$1,800 for a 50 × 12 driveway) delivered; a 3″ top-up is $0.40–$0.80 per sq ft. Grading, fabric and compaction by a contractor add $1–$3 per sq ft. The gravel driveway cost calculator breaks this down with your local prices, delivery charge and labor.

    Frequently asked questions

    How much gravel do I need for a 50 foot driveway?

    A 50 × 12 ft driveway needs about 31 tons for a full new 10″ three-layer build (two tri-axle loads), or about 8.7 tons for a 3″ top course of #57 on an existing base.

    How many tons of gravel for a driveway per 100 square feet?

    Roughly 1.45 tons per 100 sq ft for each 3 inches of #57 stone, including a 10% allowance. A full 10″ layered build is about 5.2 tons per 100 sq ft.

    How deep should a gravel driveway be?

    New driveway: 10–12 inches in three layers (4″ base, 3″ middle, 3″ top). Existing driveway top-up: 2–3 inches of #57. Heavy vehicles or clay soil: 12 inches or more, with geotextile fabric under the base.

    What is the best gravel for a driveway?

    For the surface, #57 crushed stone is the most popular all-round choice; crusher run if you want a hard, plowable surface; pea gravel only for short, flat, edged driveways. For the base, large #3/#4 stone over fabric.

    How many yards of gravel in a dump truck?

    A tri-axle carries about 14–15 cubic yards (20–22 tons) of stone; a tandem 10–12 yards; a single-axle 5–7 yards. Gravel is almost always sold and delivered by the ton.

    Do I need fabric under a gravel driveway?

    On clay, silt or any soil that stays wet, yes – a woven geotextile stops the base stone sinking into the subgrade and can halve the stone you need over the years. On sandy, well-drained ground it is optional.

    Written by the Stone & Gravel Team

    We build free calculators for landscaping and construction materials. Every density and formula on this site is listed on our methodology page. Last updated October 6, 2026.