Gravel Sizes Chart: #1 to #10, #57, #411, CA6, 2A and More Explained

On this page

    Gravel size numbers are sieve grades, not exact stone diameters: #57 is the 3/4-inch clean stone used for most driveways and drains, #1 is 2.5–4-inch rock, and #8 is 3/8-inch stone for paths and paver bedding. The chart below lists every common size in inches, whether it is clean or dense-graded, whether it compacts, what it is used for, and how much a cubic yard weighs. All weights come from our methodology page — the same figures our calculators use.

    #57 Stone Calculator

    Enter your length, width and depth to get cubic yards and tons for #57 stone in seconds.

    Open the #57 Stone Calculator →

    How gravel size numbers work

    Gravel sizes are set by the AASHTO M43 and ASTM D448 grading standards. A size number means a specified percentage of the stone passes each sieve in a stack, not that every stone is one exact diameter. The lower the number, the larger the stone: #1 is the biggest common grade and #10 is stone dust.

    Some sizes are blends of two grades. #57 is a blend of #5 and #7, and #67 is a blend of #6 and #7, which is why #57 runs coarser than #67 even though both are called 3/4-inch stone. The percent-passing table further down this page shows exactly how they differ.

    Two kinds of stone appear in the chart. Clean stone is washed, with no fines: it does not compact and water drains freely through the gaps. Dense-graded stone includes fines down to dust: it compacts into a hard surface and holds water back. That one difference decides most buying choices — clean stone for drainage, dense-graded stone for a base.

    A single inch figure for a size is always nominal shorthand. Quarries vary slightly, and the quarry’s own gradation table is the authority, not the inch figure on a price list. The ranges in the chart below are the AASHTO M43 nominal sizes, not any one seller’s figures.

    Gravel sizes chart

    Use this chart to match a size number to a job. Tons per cubic yard are from our methodology page; a dash means our methodology does not list a weight for that size.

    SizeNominal size rangeClean or dense-gradedCompacts?Typical useTons per yd³
    #12.5–4 inCleanNoRip-rap, erosion control, gabion fill—
    #21.5–2.5 inCleanNoLarge drainage, road base underlay—
    #31–2 inCleanNoFrench drains, drainage, large aggregate1.35
    #43/4–1.5 inCleanNoDrainage, driveway base layer, concrete aggregate1.35
    #53/4–1 inCleanNoConcrete aggregate, drainage—
    #571 in–No. 4 (3/16 in)CleanNoDriveway surface, French drains, concrete aggregate1.42
    #673/4 in–No. 4CleanNoConcrete aggregate, drainage—
    #83/8 in–No. 8 (3/32 in)CleanNoPaver bedding, paths, fine surfaces1.35
    #9 / #10Fines (dust and screenings)FinesYes — packs tightPaver bedding, walkway base, fill—
    Crusher run / #411 / CA6 / 2AFines to 2 in top sizeDense-gradedYes — compacts hardDriveway and road base, under pavers, shed pads1.69

    Nominal sizes are AASHTO M43 as reprinted by the Maryland Department of the Environment. Tons per cubic yard are from our methodology page only — no outside weight is used, because published #57 weights vary widely. For sizes with a dash, ask your quarry for its density or use our crushed stone calculator with the quarry’s figure.

    Reading the gradation table

    The inch range is shorthand. The real specification is the gradation table: what percentage of the stone passes each sieve. Here is the percent-passing table for the three sizes people buy most, from the ASTM D448 / AASHTO M43 size table as published in the Ohio DOT Item 703 specification.

    Sieve#57 — % passing#67 — % passing#8 — % passing
    1 1/2 in100%——
    1 in95–100%100%—
    3/4 in—90–100%—
    1/2 in25–60%—100%
    3/8 in—20–55%85–100%
    No. 40–10%0–10%10–30%
    No. 80–5%0–5%0–10%

    Percent passing means the share of the load that falls through that sieve. A dash means that sieve is not part of the published gradation for that size.

    Read #57 like this: all of it passes a 1 1/2-inch sieve, 95–100% passes a 1-inch sieve, and only 25–60% passes a 1/2-inch sieve — so most #57 stones sit between 1/2 inch and 1 inch, and “3/4-inch stone” is the shorthand name for the blend. #67 is the finer cousin: all of it passes 1 inch, 90–100% passes 3/4 inch and only 20–55% passes 3/8 inch. #8 is finer still, with 85–100% passing 3/8 inch.

    This is also why two quarries can sell “#57” that looks slightly different. Both meet the same percent-passing bands, and a single inch figure never captures the full spread. If a load matters — a drain that must flow, or concrete that must meet a mix design — ask for the quarry’s gradation sheet and check the bands, not the name.

    What “minus” means

    “3/4 minus”, written 3/4″-, means everything that passes a 3/4-inch sieve, down to dust. It is a dense-graded blend with fines included, the same idea as crusher run, and it compacts into a hard surface. It does not drain like clean #57: the fines fill the gaps that water would flow through.

    The same naming applies at other sizes. 3/8″ minus is everything 3/8 inch and smaller including dust, finer than 3/4″ minus and used for paths and as a top dressing. When a quote says “minus”, check the top size and whether fines are included, because “3/4-inch clean” and “3/4-inch minus” are different products that do opposite jobs: one drains, the other compacts.

    Regional names decoder

    Buyers get quoted local names, and the same dense-graded base is sold under a different name in almost every state. These are the same family of product — a dense-graded blend with fines that compacts hard — under the state DOT name. The quarry’s gradation table is what matters, not the name.

    NameState / specWhat it is
    CA6Illinois (IDOT)Dense-graded base; the standard Illinois base-course gradation.
    CA7Illinois (IDOT)Clean, open-graded stone; the clean counterpart to CA6.
    304Ohio (ODOT Item 304)Aggregate base course spec; the stone itself is a dense-graded blend, same family as CA6.
    21AVirginia (VDOT)Dense-graded aggregate base, same family as crusher run / #411.
    GABGeorgia (GDOT)Graded aggregate base, same family.
    2APennsylvania (PennDOT)Dense-graded base, top size 2 in, fines 0–10%. “2A Modified” is a quarry term, not an official PennDOT spec.
    2BPennsylvania (PennDOT)Clean stone; the clean counterpart to 2A.
    ABCNorth Carolina (NCDOT) and the wider SouthAggregate base course, dense-graded; the Southern name for crusher-run-type base.
    DGASeveral states, incl. KentuckyDense graded aggregate — the generic name for the same dense-graded base family.
    #411Ohio / Kentucky regionCrusher-run-type dense-graded stone (fines to dust); functionally the same as CA6 / 21A / ABC.
    AB3KansasDense-graded base, same family.

    All of the dense-graded names above weigh 1.69 tons per cubic yard in our methodology — crusher run / #411 / CA6 / 21A / DGA / ABC / 2A are one weight because they are one product family.

    Which size for which job

    Driveway. Build it in two layers. The base is a compacted dense-graded layer — CA6, #411, crusher run or 2A — and the surface is #57. One layer alone is wrong: #57 on its own shifts and ruts because clean stone does not compact, and dense-graded stone on its own holds surface water and tracks dust into the house. Work out the base with our 2A modified stone calculator and the surface with our 57 stone calculator; our guide on how deep gravel should be gives the depths for each layer, and our guide to the best gravel for a driveway compares eight stones layer by layer.

    Drainage and French drains. Use clean stone — #57, or #3 / #4 for a larger drain. The open voids between clean stones are what let water flow, and the stone also keeps the pipe from silting up. Dense-graded stone would clog a drain: its fines fill the voids and trap water instead of moving it. Work out a #3 / #4 drain with our 3/4 crushed stone calculator.

    Paths. Use #8 or pea gravel. Small stone is comfortable underfoot, packs lightly, and stays put on a path where larger stone would roll underfoot. #57 is too coarse for a walking path and will shift with every step.

    Under pavers. Lay a compacted dense-graded base first — CA6, 21A or ABC, depending on the state — then a bedding layer of #8 or coarse sand for the pavers to sit on. The base carries the load and the bedding layer lets each paver be levelled. Never lay pavers straight onto clean #57: it does not compact, so the pavers will settle unevenly.

    Concrete. #57 and #67 are the standard coarse aggregates for concrete. #67 runs slightly finer and is the more common concrete aggregate of the two; #57 is the more common choice when the same stone is also wanted for drainage on the job.

    How sizes are set

    Stone is shaken through a stack of sieves with square openings, largest at the top and smallest at the bottom. Each sieve catches what is too big to pass, and what falls through is weighed. The percentage passing each sieve is the gradation, and the quarry publishes it as a table like the one above.

    That is the whole system: a size number is a set of percent-passing bands, and the bands are what a specification checks. A load of #57 is #57 because 95–100% of it passes a 1-inch sieve and only 25–60% passes a 1/2-inch sieve — not because somebody measured a stone at 3/4 inch. When a supplier’s stone looks different from another’s, compare their gradation tables and the difference will show up there.

    Worked example: a 12 ft x 30 ft driveway surface at 4 inches of #57

    Take a driveway 12 ft wide and 30 ft long, surfaced 4 inches deep with #57 stone. This is the surface layer only — the dense-graded base underneath is a separate calculation.

    Example: 12 ft x 30 ft driveway, 4 inches of #57

    1. Area = 12 x 30 = 360 sq ft
    2. Depth in feet = 4 / 12 = 1/3 ft
    3. Volume = 360 x 1/3 = 120 cu ft
    4. Cubic yards = 120 / 27 = 4.44 cu yd (120 / 27 = 4.44)
    5. Weight = 4.44 x 1.42 tons per cubic yard = 6.3 tons (4.44 x 1.42 = 6.30)
    6. Order 7 tons — stone is sold by the whole ton, and the extra covers uneven ground

    Check it in our 57 stone calculator — it uses the same 1.42 tons per cubic yard from our methodology. For the base layer underneath, run the same sum with 1.69 tons per cubic yard, the dense-graded figure from our methodology.

    Sources

    ASTM D448 is cited by name and number in the text; its full text is paywalled, so the numbers above come from the AASHTO M43 reprint and the state DOT tables listed here.

    Frequently asked questions

    What size is #57 gravel?

    Nominally 1 inch down to No. 4 (3/16 in), and sold as 3/4-inch clean stone. 95–100% of a load passes a 1-inch sieve and only 25–60% passes a 1/2-inch sieve, so most #57 stones sit between 1/2 inch and 1 inch.

    What is the difference between #57 and #67?

    #67 tops out at 3/4 inch and runs finer; #57 runs 1 inch to No. 4. #67 is the more common concrete aggregate, while #57 is the driveway and drainage default.

    What size gravel is best for a driveway?

    Two layers: a compacted dense-graded base (CA6, #411, crusher run or 2A) with #57 on top. #57 alone shifts because clean stone does not compact; dense-graded stone alone holds surface water.

    What does 3/4 minus mean?

    Everything that passes a 3/4-inch sieve, down to dust. It is a dense-graded blend that compacts hard and does not drain like clean #57.

    Is CA6 the same as crusher run?

    Functionally yes. Both are dense-graded base blends with fines; the name depends on the state DOT spec. What matters is the quarry’s gradation table, not the name.

    Written by the Stone & Gravel Team

    We build free calculators for landscaping and construction materials. Every density and formula on this site is listed on our methodology page. Last updated November 17, 2026.