Sand, Base & Paver Calculators

Polymeric Sand Calculator

How many bags of polymeric (jointing) sand your patio needs – worked out from the paver size, joint width and joint depth, not a one-size-fits-all bag label.

  • Any paver size & joint
  • Bags & coverage
  • Free, no sign-up
Polymeric Sand Calculator
%
Polymeric sand should fill the joint to within 1/8" of the surface. Narrow 1/8" joints on 6×9 pavers use far less than wide flagstone joints – the calculator works it out from the joint geometry.
stonegravelcalculator.com
Joint sand estimate · bags
Paver size–
Area0 sq ft
Joints–
0bags
0 lb
Bag size
Joint area–
Joint volume–
Coverage per bag–
Est. cost–
Add a price for a cost estimate
How this was calculated
Estimate only. Coverage depends on joint width and depth – check the bag label for the manufacturer’s figure.
On this page

    Polymeric sand is fine sand mixed with a polymer binder; swept into paver joints and misted with water, it sets into a firm, flexible seal that stops weeds, ants and washout. Bag labels quote a coverage range so wide (“50–100 sq ft per bag”) that most people either run out or buy twice what they need. The real answer depends on how much of your patio is joint: a 24×24 slab patio with 1/8″ joints is about 1% joint, a 4×8 brick patio with 1/4″ joints is nearly 9%, and dry-laid flagstone with 1″ joints can be 10–15%. This calculator does the geometry for your paver size, joint width and paver thickness and converts it to pounds and bags.

    How to use the polymeric sand calculator

    1. Measure the paved area

      Length × width in feet, or type the square footage. For a patio and a path, add both areas.

    2. Choose the paver size and joint width

      Pick the paver from the list or enter a custom size. Most concrete pavers have spacer nibs that give 1/8″ joints; tumbled and “antiqued” pavers run 1/4–3/8″; flagstone 1/2–1″.

    3. Set the joint depth

      Normally the full paver thickness: 2 3/8″ (60 mm) for patio pavers, 3 1/8″ (80 mm) for driveway pavers, 1–1.5″ for slabs set on mortar or sand that already fills the lower joint.

    4. Read bags and coverage

      The ticket gives pounds, bags (50, 40, 20, 18 or 25 kg) and square feet per bag for your layout. The 10% allowance covers settling and the sand that is blown or swept off the surface.

    Polymeric sand formula

    Joint share = 1 − (L × W) ÷ ((L + joint) × (W + joint))
    Sand (lb) = Area (sq ft) × joint share × depth (in) ÷ 12 × 100 lb/ft³  ·  Bags = lb ÷ 50

    Example: 12 × 16 ft patio, 6 × 9 pavers, 1/4″ joints, 2 3/8″ thick

    1. Area = 12 × 16 = 192 sq ft
    2. Joint share = 1 − (6 × 9) ÷ (6.25 × 9.25) = 1 − 54 ÷ 57.8 = 6.6%
    3. Joint volume = 192 × 0.066 × 2.375 ÷ 12 = 2.5 cubic feet
    4. Weight = 2.5 × 100 lb = 251 lb; + 10% = 276 lb → 6 bags of 50 lb (about 35 sq ft per bag)

    Polymeric sand coverage per 50 lb bag

    Paver sizeJoint share (1/4″ joints)Lb per 100 sq ftBags per 100 sq ftSq ft per 50 lb bag
    4 × 8 (brick / Holland)8.7%173 lb3.529
    6 × 67.8%155 lb3.132
    6 × 96.6%131 lb2.638
    8 × 86.0%118 lb2.442
    12 × 124.0%80 lb1.663
    12 × 24 / 16 × 163.1%60 lb1.283
    24 × 242.1%41 lb0.8123

    Joints 2 3/8″ deep, sand at 100 lb/ft³, before the 10% allowance. Halve the sand for 1/8″ joints and double it for 1/2″ joints – the calculator does this exactly.

    How joint width changes the answer (6 × 9 pavers, 100 sq ft)

    Joint widthJoint shareSand per 100 sq ft50 lb bagsSq ft per bag
    1/8″ (spacer nibs)3.4%67 lb1.375
    1/4″6.6%131 lb2.638
    3/8″9.6%190 lb3.826
    1/2″12.5%248 lb5.020
    1″ (flagstone-style, 1.5″ deep)23%286 lb5.717

    This is why bag labels say 20 to 100 sq ft: the same bag covers 75 sq ft of tight-jointed pavers and 18 sq ft of flagstone.

    How to install polymeric sand

    1. Dry pavers, dry forecast. The surface and joints must be completely dry and no rain for 24 hours; above 32 °F (0 °C).
    2. Sweep it in with a push broom until the joints are full, then run a plate compactor (with a pad) or tap with a rubber mallet to settle it, and top up. Fill to 1/8″ below the paver surface or the chamfer – not flush.
    3. Blow off every grain from the paver faces with a leaf blower on low. Sand left on the surface sets as a haze.
    4. Mist in stages. Shower setting, 10–20 sq ft at a time, three light passes a few minutes apart, until water stops soaking in. Do not flood – it washes the polymer out.
    5. Keep off it for 24 hours (72 hours for vehicles).

    Polymeric sand vs regular joint sand

    Polymeric sandFine / play sandStone dust
    Sets hardYes (flexible)NoPartly
    Weeds & antsBlocksNoPartly
    WashoutResistsWashes out yearlySlow
    Max joint width1–2″ (wide-joint grades up to 4″)AnyAny
    Cost per 50 lb$25–$45$5–$8$4–$6
    Best forConcrete pavers, brick, cut flagstoneTemporary / budgetIrregular flagstone, rustic paths

    Polymeric sand cost

    Standard polymeric sand costs $25–$45 per 50 lb bag at home centers and $20–$35 at paver suppliers; premium and wide-joint grades (for joints up to 2–4″) run $45–$70. A typical 200 sq ft patio with 6×9 pavers and 1/4″ joints needs 6 bags – $150–$270. Buying one extra bag is cheap insurance against a half-filled last row; an opened bag keeps for months if it stays dry.

    Frequently asked questions

    How many square feet does a 50 lb bag of polymeric sand cover?

    Between 20 and 100 square feet, depending on the joints: about 75 sq ft for standard pavers with 1/8″ nib joints, 38 sq ft with 1/4″ joints, 20 sq ft with 1/2″ joints and under 20 sq ft for flagstone. Use the calculator for your exact layout.

    How many bags of polymeric sand do I need for 200 square feet?

    With 6 × 9 pavers and 1/4″ joints, 200 sq ft needs about 290 lb – 6 bags of 50 lb. With tight 1/8″ joints, 3 bags; for 18 × 18 flagstone with 1″ joints filled 1.5″ deep, about 6 bags.

    How deep should polymeric sand be?

    Fill the joint to within 1/8 inch of the top of the paver (or to the bottom of the chamfer). The sand must reach at least 1.5″ deep to lock the pavers, so on 60 mm pavers the full joint is normally filled.

    Can polymeric sand be used in wide joints?

    Standard grades are rated to about 1″ (some to 2″). For flagstone joints of 1–4″ use a wide-joint or “gator” type polymeric, which contains coarser aggregate. Never use it in joints narrower than 1/8″ – it cannot get down the joint.

    Why did my polymeric sand turn white or hazy?

    Sand left on the paver surface before watering, or too much water carrying polymer up onto the stones. Blow the surface clean before misting and water lightly. Light haze usually weathers off in a few weeks; stubborn haze needs a polymeric haze remover.

    How often do I need to replace polymeric sand?

    A correctly installed joint lasts 5–10 years. Pressure washing, flooding or installing it damp shortens that. Top up any joints that wash out below 1/4″ from the surface.

    Written by the Stone & Gravel Team

    We build free calculators for landscaping and construction materials. Every density and formula on this site is listed on our methodology page. Last updated October 6, 2026.