Crusher Run Calculator

Gravel & Stone Calculators

Crusher Run Calculator

Tons, cubic yards and truckloads of crusher run (crush and run, #411, ABC, road base) by compacted depth – with the 20% compaction allowance built in.

  • Compacted depth
  • 20% compaction included
  • Free, no sign-up
Crusher Run Calculator
Density:lb/ft³
%
Crusher run is ordered by compacted depth. It packs down by about 15–20% under a plate compactor, so the calculator adds 20% by default. 4" compacted for patios, walkways and shed pads, 6" for driveways, 8" or more on soft clay.
stonegravelcalculator.com
Material estimate · weigh ticket
Material–
Area0 sq ft
Compacted depth–
0tons
0 cubic yards
Volume0
Weight0
Truckloads0 ×
Est. cost–
Add a price for a cost estimate
How this was calculated
Estimate only. Densities are typical loose values – confirm with your supplier.
On this page

    Crusher run – also sold as crush and run, #411, ABC (aggregate base course), road base or 3/4″ minus – is crushed stone with the dust and small pieces left in. Those fines fill the gaps between the larger stones, so it packs into a hard, stable layer. That is why it is the standard base under driveways, patios, pavers and shed pads, and why you have to order more than the finished depth: a loose layer loses about 15–20% of its volume when you compact it. This calculator works from the compacted depth you want and adds that allowance back. New to the material? Read what crusher run is and where to use it.

    How to use the crusher run calculator

    1. Enter the area

      Length × width in feet for a driveway, patio or pad, a diameter for a round area, or type the square footage. Add extra areas for an L-shaped drive or a parking spur.

    2. Set the compacted depth

      3–4″ for walkways, patios and shed pads on firm ground, 6″ for residential driveways, 8″ or more on soft clay or where trucks will drive. The depth is measured after compaction.

    3. Pick your local name

      Crusher run / #411 / ABC is the default at 125 lb/ft³. CA-6, DGA, 2A modified and 21A are regional names for the same kind of dense-graded base. Choose “3/4″ minus” if your supplier’s product has fewer fines.

    4. Read tons and truckloads

      Crusher run is sold by the ton. The ticket shows tons, loose cubic yards and truckloads, with 20% added for compaction. Add a price per ton and a delivery fee for the total.

    Crusher run formula

    Compacted yd³ = Length (ft) × Width (ft) × Depth (in) ÷ 324
    Loose yd³ to order = compacted yd³ × 1.20  ·  Tons = loose yd³ × 1.69

    Example: 20 × 12 ft parking pad, 4 inches compacted

    1. Area = 20 × 12 = 240 sq ft
    2. Compacted volume = 240 × 4 ÷ 324 = 2.96 cubic yards
    3. Loose volume to order = 2.96 × 1.20 = 3.56 cubic yards
    4. Weight = 3.56 × 1.69 = 6.0 tons – a small single-axle load

    How much crusher run do I need? Quick reference

    Area4″ compacted6″ compacted8″ compacted
    10 × 10 (100 sq ft)2.5 t3.75 t5.0 t
    10 × 12 (120 sq ft)3.0 t4.5 t6.0 t
    12 × 20 (240 sq ft)6.0 t9.0 t12.0 t
    12 × 50 (600 sq ft)15.0 t22.5 t30.0 t
    1,000 sq ft25.0 t37.5 t50.0 t

    Crusher run at 125 lb/ft³ loose (1.69 tons per cubic yard), including the 20% compaction allowance – about 2.5 tons per 100 sq ft per 4 inches. Densities are listed on our methodology page.

    How far a ton of crusher run goes

    Spread loose, one ton of crusher run covers about 64 sq ft at 3″, 48 sq ft at 4″ and 32 sq ft at 6″. Once compacted, the same ton covers roughly a fifth less – about 40 sq ft at 4″ compacted – which is why ordering by loose coverage leaves you short.

    Crusher run vs #57 stone

    Crusher run (#411, ABC)#57 stone
    What it is3/4″ crushed stone with the dust left inClean 3/4″–1″ crushed stone, fines screened out
    Compacts?Yes – about 15–20%, into a hard layerBarely – stays loose
    DrainageSlowFast
    Weight1.69 tons per cubic yard1.42 tons per cubic yard
    Best forDriveway and paver base, shed pads, walkwaysDrainage, French drains, driveway top layer, under slabs

    A common driveway build uses both: a compacted crusher run base with 2–3″ of clean #57 or 3/4″ stone on top. Work out the top layer with the #57 stone calculator, or both layers at once with the gravel driveway calculator. The gravel sizes chart compares #57, #411 and the other common sizes side by side.

    Other names for crusher run

    Quarries sell almost the same product under local names: crush and run, #411 or #304 (Ohio, Kentucky), ABC (the Carolinas), GAB (Georgia), CR-6 (Maryland), 2A modified (Pennsylvania), DGA or QP (New Jersey), CA-6 (Illinois), 21A (Virginia) and Class 5 (Minnesota). Gradations differ slightly from state to state, but they all compact the same way. The 2A modified calculator covers the regional grades in more detail.

    How deep should crusher run be?

    • Walkways and patios – 3–4″ compacted on firm, well-drained soil; 6″ on clay. Compact in 2″ lifts.
    • Under pavers – 4–6″ compacted, then 1″ of bedding sand. The paver base calculator works out both layers.
    • Shed pads – 4″ compacted, extending about 12″ beyond the shed on every side.
    • Driveways – 6″ compacted for cars; 8″ or more on soft clay or for delivery trucks. See how deep gravel should be.

    Crusher run cost

    Crusher run is usually one of the cheapest products a quarry sells – commonly around $20–$35 per ton at the quarry and roughly $30–$65 per ton delivered, with prices rising the further you are from the quarry. Delivery is a flat fee per load, so filling the truck saves money. Get two or three local quotes and enter the price above for your own total; our gravel cost guide compares prices by stone type and our gravel driveway cost guide shows a full worked budget.

    Frequently asked questions

    How many tons of crusher run are in a cubic yard?

    About 1.69 tons (3,375 lb) of loose crusher run. One ton is about 0.59 cubic yards.

    How much area does a ton of crusher run cover?

    About 48 sq ft at 4 inches spread loose, 64 sq ft at 3″ and 32 sq ft at 6″. After compaction a ton covers roughly 40 sq ft at 4″.

    How much does crusher run compact?

    Typically 15–20% under a plate compactor. Order about 20% more than the compacted volume – the calculator does this by default.

    Does crusher run drain well?

    Not very. The fines that make it pack hard also slow water down. Use clean #57 stone where drainage matters, such as French drains or under slabs on wet ground.

    How many tons of crusher run do I need for a 12×50 driveway?

    At 6″ compacted: 600 × 6 ÷ 324 = 11.1 cubic yards, × 1.20 = 13.3 yards loose, × 1.69 = about 22.5 tons.

    Written by the Stone & Gravel Team

    We build free calculators for landscaping and construction materials. Every density and formula on this site is listed on our methodology page. Last updated November 17, 2026.