Best Gravel for Driveways: Which Stone to Use for Each Layer

On this page

    The best gravel for a driveway is not one stone but a stack of layers: a compacted crusher run base 4 to 6 inches deep, topped with 2 to 3 inches of 3/4-inch crushed stone such as #57 — with a layer of larger #3 or #4 stone underneath if the ground is soft or clay. Angular crushed stone locks together and stays where you put it; round pea gravel and river rock roll under tires. This guide gives each layer with its depth and tons per 100 square feet, compares eight common options, and shows the cheapest build that still holds up.

    Gravel Driveway Calculator

    Enter your driveway length and width to get the tons for every layer — base, middle and top — in one go.

    Open the Gravel Driveway Calculator →

    The short answer: one stone per layer

    A gravel driveway fails from the bottom up. If the base sinks into soft soil or holds water, no top stone will save it — ruts and potholes follow within a season. That is why each layer gets a different stone, chosen for a different job.

    The sub-base bridges soft or clay ground and lets water drain out from under the driveway; firm, well-drained ground can skip it. The base carries the weight: it has to compact into a hard layer, which means a dense-graded stone with fines, such as crusher run. The top layer is the wearing surface: clean, angular stone that sheds water, gives tires grip and does not turn to mud.

    LayerBest stoneDepthTons per 100 sq ftJob
    Sub-base (soft or clay ground only)#3 or #4 crushed stone (about 1.5–3 in)4 inAbout 2.0Bridges soft soil and drains water from under the base
    BaseCrusher run / #411 / ABC4–6 in compacted2.5–3.75Carries the load; compacts hard
    Top3/4-inch crushed stone (#57)2–3 in0.9–1.4Wearing surface; sheds water, gives grip

    Densities from our methodology page: #3/#4 stone 100 lb/ft³, crusher run 125 lb/ft³, #57 stone 105 lb/ft³. Sub-base and base include a 20% compaction allowance; the top layer includes 5% extra. A 6-inch base plus a 3-inch top comes to about 5 tons per 100 sq ft.

    How deep each layer should be depends on the ground and the traffic — our guide on how deep gravel should be covers the depths for cars, trucks and soft soil in detail.

    What size gravel for a driveway?

    For the surface, 3/4-inch crushed stone is the sweet spot. #57 — clean stone that mostly sits between 1/2 inch and 1 inch — is big enough that it does not stick in tire treads or get tracked into the house, and small enough to drive and walk on comfortably. Smaller stone such as #8 (3/8 inch) scatters and sticks in treads; stone of 1.5 inches and up is rough on tires and ankles and belongs in the sub-base.

    For the base, size matters less than gradation. Crusher run runs from about 3/4 inch down to dust, and it is the dust that lets it compact hard. A clean stone with no fines will not do that job, however big it is. Our gravel sizes chart explains what each size number means and the local names for the same products.

    8 driveway gravel options compared

    These are the stones most often quoted for driveways, judged on the three things that decide whether a driveway lasts: does it compact, does it drain, and does it stay put under tires.

    StoneCompacts?Drains?Stays put?Bulk price per tonBest use
    Crusher run / #411 / ABCYes, hardSlowlyYes$18–$35Base; whole surface on rural drives
    #57 / 3/4″ clean crushed stoneBarelyYes, fastYes, over a firm base$15–$30Top layer
    #3 / #4 crushed stoneNoYes, fastYes, but rough underfootAsk locallySub-base on soft ground
    Crushed limestone (3/4″ with fines)YesModeratelyYes$30–$40Top course that packs firm
    Crushed graniteYes, when it has finesModeratelyYesAsk locallyHard-wearing top course where it is quarried
    Recycled concreteYesModeratelyYesAbout 30–50% below new stoneLow-cost base layer
    Pea gravel (3/8″, rounded)NoYesNo — rolls and ruts$28–$45Paths and patios, not driveways
    River rock (1–3″, rounded)NoYesNo$45–$130Decorative borders only

    Prices checked November 2026, from our gravel cost guide (bulk, at the yard, before delivery). Prices vary a lot with distance from the quarry — get two or three local quotes.

    Why pea gravel and river rock make poor driveways. Both are rounded. Round stones cannot interlock, so every tire pushes them aside: they rut within weeks, spray onto the lawn, and are hard work to walk or wheel a bin across. They drain well and look good, which is why they are popular for paths and borders — but under a car they never settle. If you love the look, use them as an edging strip beside a crushed-stone surface.

    Crushed limestone or granite? Both work as a 3/4-inch top course. Limestone is cheaper across much of the country and packs firm, but it is a softer stone that slowly wears down into fines — fine for a family car, dustier under heavy traffic. Granite is harder and lasts longer, but costs more anywhere far from a granite quarry. Buy whichever hard, angular stone your nearest quarry produces; the haul distance usually decides the price more than the rock type.

    Climate, slopes and heavy vehicles

    Wet ground and freeze–thaw. Water under the driveway is what breaks it up. On clay or poorly drained soil, add the #3 or #4 sub-base and lay geotextile fabric on the soil first so the stone does not sink into the mud. Keep the top layer clean and free-draining so rain runs off and through instead of sitting in the surface and freezing.

    Slopes. Loose clean stone creeps downhill and washes out in heavy rain. On a steep drive, a surface that compacts — crusher run, crushed limestone with fines, or a purpose-made driving surface mix — holds better than loose #57. Penn State’s Center for Dirt and Gravel Roads developed one such mix, Driving Surface Aggregate (DSA): a crushed-stone blend designed specifically as the wearing surface of unpaved roads, placed 6 to 8 inches deep (uncompacted) in a single lift. Some quarries, especially in Pennsylvania, sell it by name. Whatever the stone, turn water off the drive at intervals rather than letting it run the full length.

    Heavy vehicles. Delivery trucks, RVs, boats on trailers and farm equipment need a thicker base: 8 inches or more of compacted crusher run, with the sub-base on anything soft. A base that is too thin is the most expensive mistake on a driveway, because the only fix is to dig it out and start again.

    The cheapest driveway gravel that still works

    The cheapest build that holds up is crusher run on its own, 6 inches compacted, used as both base and surface. It is among the lowest-priced stones a quarry sells, it compacts into a hard surface, and it arrives in one delivery. At 3.75 tons per 100 sq ft and $18 to $35 a ton, that is roughly $68 to $131 of stone per 100 sq ft. The trade-off: it is dusty in dry weather, it can get slick and muddy in low spots, and it needs a good crown to shed water.

    Adding a 3-inch #57 top layer costs about another 1.4 tons per 100 sq ft — around $21 to $41 more at $15 to $30 a ton — and gives you a cleaner, better-draining surface. Recycled concrete is the other way to save: use it for the base and put new stone on top. What does not save money is skimping on depth. A thin base ruts and potholes, and you end up buying the stone twice.

    Worked example: a 12 x 50 ft driveway on firm ground

    A single-car driveway, 12 ft wide and 50 ft long, on firm, well-drained soil: no sub-base, a 6-inch compacted crusher run base and a 3-inch #57 top.

    Compacted yd³ = Length (ft) x Width (ft) x Depth (in) / 324 · Tons = yd³ x tons per cubic yard

    Example: 12 ft x 50 ft driveway, 6 in crusher run base + 3 in #57 top

    1. Area = 12 x 50 = 600 sq ft
    2. Base, compacted: 600 x 6 / 324 = 11.11 cu yd; loose to order x 1.20 = 13.33 cu yd
    3. Base weight: 13.33 x 1.69 tons per cubic yard = 22.5 tons of crusher run
    4. Top: 600 x 3 / 324 = 5.56 cu yd x 1.42 tons per cubic yard = 7.9 tons; with 5% extra = 8.3 tons of #57
    5. Total: 22.5 + 8.3 = about 31 tons — the same as the shortcut of about 5 tons per 100 sq ft (6 x 5.1 = 30.6)
    6. Stone cost: 22.5 x $18 to $35 = $405 to $788 for the base, plus 8.3 x $15 to $30 = $125 to $249 for the top = about $530 to $1,040 before delivery

    Thirty-one tons is two or three truckloads, so ask each supplier for a delivered price and compare totals, not per-ton figures. Check the numbers for your own driveway in our gravel driveway calculator, or work out a single layer with the crusher run calculator, the 57 stone calculator or the crushed stone calculator. For the full installed budget — delivery, spreading and compaction — see our gravel driveway cost guide.

    Edging and crown

    Crown it. A gravel driveway needs a steeper side slope than a paved one, because water soaks into a loose surface instead of running off. Penn State’s Center for Dirt and Gravel Roads recommends a crown or cross-slope of 1/2 to 3/4 inch of fall per foot of width for unpaved surfaces — about 4 to 6 percent, against roughly 2 percent for pavement. On a 12 ft driveway crowned down the middle, that puts the centre about 3 to 4.5 inches higher than the edges.

    Edge it. Steel, treated timber, concrete or a row of setts along each side stops the top layer spreading into the lawn and keeps the edges from crumbling. Set the edging so the finished gravel sits just below its top. Re-grade the surface before ruts get deep: a light pass with a rake or a box blade once or twice a year keeps the crown, and the drive, in shape.

    Sources

    Frequently asked questions

    What is the best size gravel for a driveway?

    3/4-inch crushed stone, such as #57, for the top 2 to 3 inches, over 4 to 6 inches of compacted crusher run. On soft or clay ground, add 4 inches of larger #3 or #4 stone underneath. Avoid anything smaller than about 1/2 inch on the surface — it sticks in tire treads and scatters.

    Is pea gravel good for a driveway?

    Not as the driving surface. Pea gravel is round, so it cannot lock together: tires push it aside, it ruts quickly and it sprays onto the lawn. It works well for paths and patios. For a driveway, use angular crushed stone on top and keep pea gravel for borders.

    What is the cheapest driveway gravel?

    Crusher run, at about $18 to $35 a ton, or recycled concrete where it is available. Six inches of compacted crusher run on its own is the cheapest driveway that still holds up — roughly $68 to $131 of stone per 100 sq ft before delivery. Prices checked November 2026.

    Crushed limestone or granite for a driveway?

    Either works as a 3/4-inch top course. Limestone is usually cheaper and packs firm, but it is softer and slowly wears into dust under heavy traffic. Granite is harder and lasts longer, but costs more away from granite quarries. Buy the hard, angular stone your nearest quarry produces.

    How do I stop driveway gravel washing away?

    Give the driveway a crown of 1/2 to 3/4 inch per foot, turn water off the surface at intervals instead of letting it run the full length, use a stone that compacts on steep sections, edge both sides, and re-grade before ruts deepen. Loose clean stone on a slope will always creep downhill.

    Written by the Stone & Gravel Team

    We build free calculators for landscaping and construction materials. Every density and formula on this site is listed on our methodology page. Last updated November 17, 2026.